View MSK4454U_1284413.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ISO-9001 CERTIFIED BY DSCC
M.S.KENNEDY CORP. M.S. KENNEDY CORP. FEATURES:
10 AMP, 600 VOLT IGBT SMART POWER 3-PHASE MOTOR DRIVE HYBRID
4454
(315) 701-6751
4707 Dey Road Liverpool, N.Y. 13088 600V,10 Amp Capability Ultra Low Thermal Resistance - Junction to Case - 2.2C/W (Each IGBT) Self-Contained, Smart Lowside/Highside Drive Circuitry Bootstrap High-Side Supplies Under-Voltage Lockout Capable of Switching Frequencies to 25KHz Isolated Case Allows Direct Heat Sinking Bolt-down Design Allows Superior Heat Dissipation
DESCRIPTION:
The MSK 4454 is a 10 Amp, 3 Phase Bridge Smart Power Motor Drive Hybrid with a 600 volt rating on the output switches. The output switches are Insulated Gate Bipolar Transistors (IGBT's). The free-wheeling diodes are Fast Recovery Epitaxial Diodes (FRED's) to provide matched current capabilities with the IGBT's and are specified with excellent reverse recovery times. This new smart power motor drive hybrid is 5.0 volt input logic compatible. Under-voltage lockout shuts down the bridge when the supply voltage gets to a point of incomplete turn-on of the output switches. The internal high-side bootstrap power supply derived from the +VB supply completely eliminates the need for 3 floating independent power supplies.
EQUIVALENT SCHEMATIC
TYPICAL APPLICATIONS TYPICAL APPLICATIONSPIN-OUT INFORMATION
PIN-OUT INFORMATION
1 2 3 4 5 6 7 8 9 10 H INA L INA +VCC H INB L INB COM COM +VB H INC L INC 20 19 18 17 16 15 14 13 12 11 V+ N/C AVAO N/C BVBO N/C CVCO
Rev. B 11/04
3 PHASE SIX STEP DC BRUSHLESS MOTOR DRIVE OR 3 PHASE SINUSOIDAL INDUCTION MOTOR DRIVE
1
2.7C/W
ELECTRICAL SPECIFICATIONS
MSK 4454 Typ. Max.
Parameters
Test Conditions 2
Min.
UNITS
OUTPUT CHARACTERISTICS Ic=10A VC-E (On) Voltage (Each IGBT) 3 V+ = 600V Leakage Current (Each IGBT) ID=10A Instantaneous Forward Voltage (FRED Flyback Diode) 3 ID=10A, di/dt=100A/S, Vr=350V Reverse Recovery Time BIAS SUPPLY CHARACTERISTICS +Vcc=15V +Vcc Bias Current +VB=15V +VB Bias Current INPUT SIGNAL CHARACTERISTICS 1 +Vcc=15V Positive Trigger Threshold Voltage +Vcc=15V Negative Trigger Threshold Voltage +Vcc Positive Going Threshold Under-voltage Lockout +Vcc Negative Going Threshold Low Side Turn-off to High Side Turn-On Dead Time High Side Turn-off to Low Side Turn-On
2.7 7.2 6.7 280 4
3.1 250 1.75 8.9 8.2 400 5
3.8 500 2.5 180 6 1 0.8 10.8 9.9 520 6
NOTES: 1 Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. 2 Vcc=+15V, VB=+15V, V+=270V and TCASE=25C unless otherwise specified. 3 Measured using a 300S pulse with a 2% duty cycle.
2
Rev. B

2.2C/W

-40C to +85C +150C
volts A volts nS mA mA volts volts volts volts nSEC SEC

ABSOLUTE MAXIMUM RATINGS V+ High Voltage Supply VCC Logic Supply IOUT Continuous Output Current IPK Peak Output Current JC Thermal Resistance @ 125C (Output Switches)(Junction to Case) JC Thermal Resistance @ 125C (Diodes)

600V 18V 10A 30A
TsT Storage Temperature Range TLD Lead Temperature Range TC (10 Seconds) Case Operating Temperature MSK 4454 TJ Junction Temperature
-55 to +125C 300C
11/04
TYPICAL PERFORMANCE CURVES
3
Rev. B
11/04
APPLICATION NOTES MSK 4454 PIN DESCRIPTIONS
+VCC - Is the low voltage supply for all the internal logic and drivers. A 0.1 F ceramic capacitor in parallel with a 10F tantalum capacitor is the recommended bypassing from the +VCC pin to the COM pin. H INA, H INB, H INC - Are high active logic inputs for signalling the corresponding phase high-side switch to turn on. The logic inputs are compatible with standard CMOS or LSTTL outputs. These logic inputs are internally zener clamped at 5.2 volts. L INA, L INB, L INC - Are low active logic inputs for signalling the corresponding phase low-side switch to turn on. The logic inputs are compatible with standard CMOS or LSTTL outputs. These logic numbers are internally zener clamped at 5.2 volts. AO, BO, CO - Are the pins connecting the 3 phase bridge switch options. AV-, BV-, CV- - Are the connections from the bottoms of the three half bridges. These pins get connected to the COM pin. If current sensing is desired they may be connected to the COM pin through a low value sense resistor. +VB - Is the connection used to provide power to the floating high-side bootstrap supplies in the gate drive circuitry. V+ - Is the high voltage positive rail connection to the tops of the three half bridges. Proper power supply bypassing must be connected from this pin to the COM pin for good filtering. This bypassing must be done as close to the hybrid as possible. COM - Is the connection that all hybrid power supply connections are returned to and bypassed to.
4
Rev. B
11/04
TYPICAL SYSTEM OPERATION
The MSK 4454 is designed to be used with a +270 volt high voltage bus, +15 volt low power bus and +5 volt logic signals. Proper derating should be applied when designing the MSK 4454 into a system. High frequency layout techniques with ground planes on a printed circuit board is the only method that should be used for circuit construction. This will prevent pulse jitter caused by excessive noise pickup on the current sense signal or the error amp signal. Ground planes for the lower power circuitry and the high power circuitry should be kept separate. The connection between the bottom of the current sense resistor, COM pin and the high power ground, AV-, BV- and CV- pins are connected at this point. This is a critical path and high currents should not be flowing between the current sense and COM. Inductance in this path should be kept to a minimum. An RC filter (shown in 2 places) will filter out the current spikes and keep the detected noise for those circuits down to a minimum. In the system shown a PWM pulse by pulse current limit scheme controlled by the motor controller is implemented. When controlling the motor speed by the PWM method, it is required that the low side switches be PWM pulsed due to the bootstrap supplies used to power the high side switch drives. The higher the PWM speed the higher the current load on the drive supply. PWM of the low side will prevent sagging of the high side supplies. A separate pin (+VB) is provided for connecting an external floating power supply to power the bootstrap supplies.
5
Rev. B 11/04
MECHANICAL SPECIFICATIONS
ESD Triangle Indicates Pin 1. NOTE: ALL DIMENSIONS ARE 0.010 UNLESS OTHERWISE LABELED.
ORDERING INFORMATION
Part Number MSK4454S MSK4454D MSK4454U MSK4454G Screening Level Industrial Industrial Industrial Industrial Lead Configuration Straight Down Up Gull Wing
M.S. Kennedy Corp.
4704 Dey Road, Liverpool, New York 13088 Phone (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products. Please visit our website for the most recent revision of this datasheet.
6
Rev. B 11/04

▲Up To Search▲

Price & Availability of MSK4454U

	To Download MSK4454U Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .